1911 Series80 Optimizing Springs
1911 Series80 Optimizing Spring System
90 Item Items
Warning: Last items in stock!
Tune-Up and Optimization Spring Kit Solution
Solution: The BHSpringSolutions 1911 Optimizing Spring Kit
All BHSpringSolutions Optimizing Spring Kits, for the 5” barrel 1911 .45ACP, contain 3 Recoil Springs, 2 Main Springs, Optimal Firing Pin Spring, Plunger Spring, Magazine Latch Spring, and a Firing Pin Block Safety Spring in the Series 80 kits.
Why 3 Recoil Springs and 2 Main Springs?
Generally, the distance of ejection of empty shell casings, gives us feedback about function and slide velocity. And generally, we look for this distance to be in the 4’ – 8’ range. This is where “All 1911s are not created equal”, applies. During our testing with 230 gr standard pressure ammunition, we found distance of empty case ejection to be in the 4’ – 6’ range with our standard 16 lb recoil spring and our Heavy Main Spring. When we changed over to our Light Main Spring, distance of empty shell case ejection was an additional 1½’ – 2 ½’ further, depending on the ammunition being tested….giving us empty case ejection in the 6’ – 8’ range. With the lighter main spring, we could then go to our heavier 18 lb recoil spring, and tame the recoil a bit, and reduced the empty shell case ejection distance and increased the authority of the slide’s return to battery. Our 18 lb Recoil Spring also nicely controlled +P .45ACP ammunition, particularly with the heavier main spring. These results were in our 1911 used for testing which is a recent production Remington R1. The owner of a Colt GI 1911, made in 1930, may find a slightly different combination to be optimal, and the owner of a Springfield 1911 may find yet a different combination to work best. And also, the right combination of Main Spring and Recoil Spring is not only about the basic science involved in measuring distance of empty shell casings – there is another factor – not all shooters are created equal. Our 3 Recoil Springs and 2 Main Springs, standard in all BHSpringSolutions 1911 Spring Kits, also take into account this other important fact: “It’s also a feel thing”……in other words, as long as function is reliable and the empty shell casing ejection distance is in the desired range, the right combination of recoil spring and main spring, in a particular 1911, for a particular shooter, also depends on which combination yields the best performance results for the shooter and his 1911. Many 1911s will function reliably with our 16 lb recoil spring and either of our Main Springs, and many 1911s will function well with standard pressure ammunition with our heavier 18 lb recoil spring and lighter Main Spring as a combination – and the final determination of “optimal” will be based on the combination that “feels” best, and enables the owner/shooter to perform best. Ultimately, this optimal combination is found by the 1911 owner and his handgun, together.
Many manufacturers go to great efforts to make quality 1911s, with consistency of build quality that, given today’s technology and modern machinery, is better than it’s ever been in history. Unfortunately, many 1911 owners (and manufacturers) are missing the best possible 1911 performance by not finding the best possible combination of Recoil and Main Spring. The importance of these two springs, working together like gears in a well-oiled machine, cannot be overstated with respect to the 1911.
What is the difference between a “Series 70” and a “Series 80” 1911?
The Series 80 is a more modern design, containing a mechanical firing pin block safety, intended to prevent accidental discharge if the 1911 should be dropped on the muzzle with a live round in the chamber, by preventing the firing pin from moving forward except when the trigger is pulled. Series 70 1911s contain no such device and are fully dependent on the strength of the Firing Pin Spring, to retain Firing Pin in it’s rearward position, in the event the 1911 is dropped on the muzzle with a live round chambered.
What is the difference between a Series 70 and a Series 80 Spring Kit from BHSpringSolutions LLC?
Series 80 Spring Kits from BHSpringSolutions LLC contain a Firing Pin Block Safety Spring, a light Firing Pin Spring, and one each of our Heavy and Light Main Springs.
Series 70 Spring Kits from BHSpringSolutions LLC contain an enhanced (heavier) Firing Pin Spring because, the Firing Pin Spring itself is your only protection against accidental discharge in the event of a muzzle drop in the Series 70 design.
More On Main Springs
Each Series 70 kit contains one Heavy Main Spring, and 2 Light Main Springs.
Because of the enhanced resistance created by the Series 70 Firing Pin Spring, shooters who prefer performance associated with the Light Main Spring should note that we suggest replacement of this Light Main Spring twice as often as other springs in the 1911 Series 70. BHSpringSolutions recommends a “best practices” approach to 1911 spring replacement of “Every 5 Years or 5,000 rounds, whichever comes first”. The one exception is use of the Light Main Spring in combination with the Heavy Firing Pin Spring of the Series 70 – in which case we recommend replacement of the Light Main Spring at approximately 2 ½ years – this is the reason for two Light Main Springs in our Series 70 1911 Tune-Up and Optimization Spring Kits.
Contained in all BHSpringSolutions LLC 1911 Optimizing Spring Kits. This multi-function spring is located inside the little tube you see on the left side of your 1911. One responsibility of this spring is keeping the manual safety in the “on safe” position. And, since “cocked and locked” also known as “Condition 1”, is the most common condition for carry of the 1911, keeping this spring healthy should be a priority for all 1911 owners. A healthy plunger spring reduces the chances of unintended movement of the manual safety from the “on safe” position to “fire” position. A correctly made plunger spring has an intentional “dog leg” in the center of the spring because this design works best. The Plunger Spring must push in opposite directions, simultaneously, all the time. The “kink”, or dog leg in the center of this spring creates a stationary position in the center of the spring because each half of the spring has it’s own job to do, in opposing directions. A side benefit is that the Plunger Spring doesn’t fly across the room during disassembly when it’s made with the “dog leg” design.
Magazine Latch Spring:
This spring is responsible for positive lock-up and retention of the magazine in the 1911 grip frame. If you read many handgun reviews, it probably won’t be long before you read a reviewer who comments that he or she unintentionally manipulated the magazine release during shooting or deholstering. Of course, no magazine latch spring can stop this from happening if a shooters thumb is going places it shouldn’t go at the wrong time…….but a healthy magazine latch spring does decrease the likelihood of untended manipulation of the magazine release, as much as possible. A healthy magazine latch spring provides maximum resistance on the magazine release, while still allowing smooth manipulation and function when release of the magazine is intended.
No customer comments for the moment.