" Tactical " Fast Safety (SFS v2.0) for Hi-Power with Ambi Mag Catch, BHSpring Kit and Checkered Masters Grips
598 Item Items
Warning: Last items in stock!
This is the updated version (Second Generation) of the Safety Fast Shooting system. Equipped with BHSpringSolutions LLC SFS springs by default. Also included in the package:
1. 17 lb. Recoil Spring
2. Optimizing Trigger Springs
- Tactical (2-coils)
- Target (3-coils)
3. Optimized Sear Lever Spring
4. Firing Pin Spring
5. Extractor Spring
(produced for FN Browning Hi-Power. Not a drop-in part in clones like FEG, Arcus, CD, Inglis, Kareen...)
The Benefits of the SFS (Fast Shooting) System:
⦁ FS System allows the Hi Power to be carried Condition 1, but in a Hammer Forward state. When the Manual Safety (termed the “Cocking Lever” with the FS system) is swiped off, the hammer simultaneously springs to the cocked/ready to fire position by work of a Spring.
⦁ Because of the almost flat hammer profile and hammer-forward “carry” position of the hammer, the Hi Power can be carried Condition 1 and eliminate common “snagging” in clothing of a cocked Hi Power hammer.
⦁ Most comfortable hammer for Carry (doesn’t dig into your side-fat when carried IWB on the hip) Makes the Hi Power feel more like a Striker-Fired Concealed Carry handgun, except better because of the Hi Powers thin profile.
⦁ Best Solution for More Sure and Fast One Handed Deployment of the Hi Power.
⦁ Enables “Hammer Forward Carry”, (like a DA/SA handgun), with the superior benefit of every shot being the same Single Action Trigger Pull.
⦁ Adds an Extended Slide Stop/Slide Release…Making all the Hi Powers Controls easily within reach of the thumb of the shooting hand, without releasing or adjusting grip on the Hi Power.
⦁ Adds Ambidextrous Safety to older Hi Powers with one-sided safety.
⦁ Cleaner/Crisper Trigger Break – The FS System is a group of parts and springs that replace certain parts of the Traditional Operating System. Two parts replaced are the Sear and Hammer. Typical feedback from gunsmiths: “The FS Hammer and Sear are extremely well made, and typically superior to the FN/Browning OEM Sear/Hammer. It is not uncommon for a non-modified Browning trigger pull to go like this: “Take up…….wall……you think you’re at the “break” of the trigger……then you pull a little more into a “zone” that allows the trigger to pull a little more and yet still the trigger doesn’t break…..so with more pressure……..FINALLY!........the hammer falls!” The FS Sear/Hammer set typically eliminates THAT! (Note: All results do vary slightly)
⦁ Adds a “Drop Safety” to the Hi Power (that doesn’t degrade trigger pull!) When in the “On Safe” position, both Slide and Hammer are locked.
⦁ Persons who miss-out on the benefits of Hi Power Carry because they don’t like “Cocked and Locked” Carry,for any reason, can usually embrace Condition 1 FS Hammer Forward Carry.
⦁ “FS Critics” who mention that the FS System “adds a spring”. Fact-Check: The FS System Replaces Three Springs in a Hi Power: Hammer (Main) Spring, Safety Lever Spring, the flat metal Sear Spring, and adds a new “Return Spring” that is the cause of the Hammer’s Cocking Action when the Safety is swiped off. The Springs associated with the SFS system are more resilient and reliable than the Hi Power’s Extractor Spring. And, like every other function of the Hi Power, the function of the FS System is dependent on the health of the springs involved with it’s action. BHSpringSolutions LLC manufactures Optimized FS Main Spring, Cocking Lever Spring, and Return Spring. In the opinion of BHSpringSolutions LLC, the design of FS springs is appropriate for the jobs these springs perform and none of these springs could be considered “over-worked” because of the job performed.
⦁ Seeing the Hammer Forward provides visual confirmation that the Hi Power is “on safe”. Eliminates all “THAT HAMMER IS COCKED!” concerns.
⦁ Transition to FS is seamless for Cocked and Locked carriers of the Hi Power.
⦁ Safe Condition 1 Carry, easily embraced by Hi Power owners currently using a “Condition 2 or Condition 3 Carry. (Also safer because of the “no-snag” hammer.)
⦁ MAY buy you a few extra seconds to access your Back-Up Weapon if an attempted Gun Grab is successful and your Hi Power ends up in a bad-guys hand. The FS System is different and may cause momentary confusion for an attacker who gains control or your Hi Power. In the FS Carry Condition 1, the Hammer is Locked and cannot be manually cocked. The Slide is Locked and cannot be racked. When the Safety is disengaged, it causes the hammer to spring rearward – again, different, and may cause momentary confusion for an attacker in a Gun Grab. At a minimum, in a “Gun Grab” situation, your Hi Power might be more difficult for an attacker to deploy than any “non-manual-safety” semi-auto pistol. SFS has Tactical Safety Advantages over ANY other operating system on any handgun.
⦁ Fastest Hi Power Field Strip procedure. User no longer needs to lock back the slide, to remove the Slide Stop/Slide Release. Simply push out Slide Stop wh while applying slight upward pressure on the Slide Stop.
⦁ If shooter tends to “ride the manual safety” with shooting thumb during shooting, nothing changes. But, since the FS Manual Safety cannot be “cammed up” with the thumb (only by manually pushing forward the hammer), FS eliminates the chance of the thumb riding up under the safety and inadvertently engaging the safety.
⦁ Ambidextrous Magazine Catch
If you want this package to be installed in our service centre, please make you selection from the drop down menu. A return shipping fee to your FFL is added to the price of the service. Please download the service centre forms, fill them in and send them to us via email or fax.
No customer comments for the moment.